quality control comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Updated 2026-01-03. Numbers and descriptions here follow the published literature rather than marketing material.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
=== Products === PFAS are used to produce fluoropolymers by emulsion polymerization. Because they resist heat, oil, stains, grease, and water, they are ingredients in stain repellents, polishes, paints, and coatings. They came into use with the invention of Teflon in 1938. They have been used in products including waterproof fabric such as nylon, yoga pants, carpets, shampoo, feminine hygiene products, mobile phone screens, wall paint, furniture, adhesives, food packaging, firefighting foam, the insulation of electrical wires, dental floss and sunscreen. PFAS have been used by the cosmetic industry in cosmetics and personal care products, including lipstick, eye liner, mascara, foundation, concealer, lip balm, blush, and nail polish. Pesticides including fluazinam and flufenacet break down to produce trifluoroacetic acid. In 2025, a report by the US FDA stated that in 2021, up to 1.4% of cosmetics sold in Europe contained PFAS and as of 2025, less than 1% of cosmetics sold in the US contained PFAS.
== Industrial functionality == A number of halogenated compounds are environmentally toxic industrial by-products, and it has been suggested that haloalkane dehalogenases may be useful catalysts for their biodegradation, with potential applications in bioremediation. In biocatalysis, there is a standing interest in these enzymes, particularly for the production of optically pure alcohols. Therefore, the identification of dehalogenating enzymes with appropriate selectivity patterns is very important in terms of their industrial utility.
== Software Packages == Many chromatography software packages are provided by manufacturers, and many of them only provide a simple interface to acquire data. They also provide different tools to analyze this data. The following is a list of software and the (unexplained) tools that each provides. Please note that some of them were discontinued with the years.
=== New Zealand === The opposition Green Party of Aotearoa New Zealand's co-leader, Marama Davidson, stated "this is a unilateral attack that goes against any enduring pathway to international peace through justice." She called upon Prime Minister Christopher Luxon to condemn the United States for attacking Venezuela.
Sources: en.wikipedia.org
== Variants == When the total electron excitation energy of colliding particles is sufficient, then the bonding energy of two particles that bonded together can also be contributed into the associative penning ionization act. Associative Penning ionization can also occur:
=== Brazil === The 2009 Brazilian Federal Law 11.903 and subsequent regulations of the National Agency for Sanitary Surveillance in Brazil (ANVISA) require that a 2D data matrix code be put on all secondary packaging. Under these provisions, manufacturers will be required to maintain a database of all transactions from manufacturing to dispensing, while distributors must report serialized transaction data to the manufacturer and keep a database of suppliers, medicine recipients, and packing companies. Data Element – National Number, Expiration Date, Batch/Lot Number, Serial Number
"The Nixon White House panicked," wrote political editor Christopher Caldwell, and declared drug abuse "public enemy number one". By 1973, there were 1.5 overdose deaths per 100,000 people. There were fewer than 3,000 overdose deaths in 1979, when a heroin epidemic was raging in U.S. cities. There were fewer than 5,000 recorded in 1988, around the height of the crack epidemic. More than 64,000 Americans died from drug overdoses in 2016, according to the U.S. Centers for Disease Control and Prevention. Modern prescription opiates such as Vicodin and Percocet entered the market in the 1970s, but acceptance took several years and doctors were apprehensive about prescribing them. Until the 1980s, physicians had been taught to avoid prescribing opioids because of their addictive nature. A brief letter published in the New England Journal of Medicine (NEJM) in January 1980, titled "Addiction Rare in Patients Treated with Narcotics", was frequently cited to downplay such concerns. The NEJM reexamined the 1980 letter in June 2017, pointing out among other things that the conclusions were based on hospitalized patients only, and not on patients taking the drugs after they were sent home. The letter's original author, Hershel Jick, has said that he never intended for it to justify widespread opioid use.
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.